Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process (Includes all amendments And changes 1/16/2017).
Automaticky přeložený název:
Standard Specification pro ocelový plech, Twin-Roll Cast, pozinkovaný (pozinkované) do žárovým procesu
NORMA vydána dne 1.11.2011
Označení normy: ASTM A1063/A1063M-11a
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2011
Kód zboží: NS-1269
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
alloyed coating, direct cast steel, high strength low alloy, minimized spangle coating, sheet steel, spangle, steel, steel sheet, structural steel, zinc, zinc coated (galvanized), zinc iron-alloy, zinc iron-alloy coated: Hot-dip processed coatings, Steel sheet, Twin-roll casting, Zinc-coated steel sheet, ICS Number Code 77.140.50 (Flat steel products and semi-products)
1. Scope | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers steel sheet, produced by the Twin-Roll Cast Process (see Appendix X2) and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths. Note 1—See Appendix X2 for a description of the Twin-Roll Cast process. 1.2 The product is produced in various zinc coating weights [masses] or coating designations as shown in Table 1. 1.3 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M unless otherwise provided herein. 1.4 The product is available in a number of designations, grades and classes and in the two following general categories that are designed to be compatible with different application requirements. 1.4.1 Steels with mandatory chemical requirements and typical mechanical properties. 1.4.2 Steels with mandatory chemical requirements and mandatory mechanical properties. 1.5 This material is available in the following sizes: 1.5.1 Thickness—up to 0.078 in. [2.0 mm] 1.5.2 Width—up to 79 in. [2000 mm] 1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification. 1.7 This specification is applicable to orders in either inch-pound units (as A1063) or SI units (as A1063M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other. 1.8 Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Weight [Mass] of Coating RequirementsA, B, C Note— Use the information provided in 8.1.2 to obtain the approximate coating thickness from the coating weight [mass].
A The coating designation number is the term by which this product is specified. Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the zinc coating is not always evenly divided between the two surfaces of a coated sheet; nor is it always evenly distributed from edge to edge. However, the minimum triple-spot average coating weight (mass) on any one side shall not be less than 40 % of the single-spot requirement. B As it is an established fact that the atmospheric corrosion resistance of zinc coated sheet products is a direct function of coating thickness (weight (mass)), the selection of thinner (lighter) coating designations will result in almost linearly reduced corrosion performance of the coating. For example, heavier galvanized coatings perform adequately in bold atmospheric exposure whereas the lighter coatings are often further coated with paint or a similar barrier coating for increased corrosion resistance. Because of this relationship, products carrying the statement “meets ASTM A1063/A1063Mrequirements” should also specify the particular coating designation. C No minimum means that there are no established minimum requirements for triple- and single-spot tests. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Historická
1.10.2011
Historická
1.10.2011
Historická
1.10.2013
Historická
1.10.2013
Historická
1.10.2013
Historická
1.10.2013
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.