Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A1018/A1018M-18
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
Přeložit název
NORMA vydána dne 15.5.2018
Informace o normě:
Označení normy: ASTM A1018/A1018M-18
Poznámka: NEPLATNÁ
Datum vydání normy: 15.5.2018
Kód zboží: NS-851263
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A1018/A1018M-18 :
Keywords:
carbon steel sheet, carbon steel strip, commercial steel, drawing steel, heavy-thickness coils, high-strength low-alloy steel, hot-rolled steel sheet, hot-rolled steel strip, improved formability, steel sheet, steel strip, structural applications, ultra-high strength steel,, ICS Number Code 77.140.20 (Steels of high quality)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||
|
1.1 This specification covers hot-rolled, heavy-thickness coils beyond the size limits of Specification A1011/A1011M. 1.2 The product is available in six designations: Commercial Steel, Drawing Steel, Structural Steel, High-Strength Low-Alloy Steel, High-Strength Low-Alloy Steel with Improved Formability, and Ultra-High Strength Steel. 1.3 This material is available only in coils described as follows:
Note 1: The changes in width limits with the publication of
A635/A635M – 06a result in a
change in tensile testing direction for material from 0.180 in.
[4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in.
[1200 mm] wide as that material is now covered by Specification
A568/A568M – 06a. The
purchaser is advised to discuss this change with the
supplier.
1.4 Sheet and strip in coils of sizes noted in 1.3 are covered by this specification only with the following provisions: 1.4.1 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.4.2 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils). Plate converted from coils is no longer governed by this sheet steel specification and since this material is now a plate, the requirements of the appropriate plate specification shall apply, except in cases where there is a conflict between the requirements of the plate specification and this specification. In these cases, the more restrictive limits of either specification shall apply. 1.4.3 The dimensional tolerances of Specification A635/A635M are applicable to material produced to this specification. 1.4.4 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||
|
Doporučujeme:
EviZak - všechny zákony včetně jejich evidence na jednom místě
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
