ASTM C1821/C1821M-16(2021)e1 - 1.1.2021
 
Significance and Use

4.1?This practice is useful as a reference by an owner and/or the engineer in preparing project specifications.

4.2?The practice is useful as a reference by an owner, engineer, or installing contractor to properly install precast concrete circular manholes.

 
1. Scope

1.1?This practice covers the procedures to be followed in the planning, site preparation, installation, testing and backfilling of underground vertical reinforced circular precast concrete manholes and components manufactured in accordance with Specification C478/C478M and used in sewer, drainage, and water works.

1.2?Concrete pipe and box culverts are not covered under this practice. Also, precast concrete utility structures covered in Specification C858 are excluded from this practice.

1.3?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

 
2. Referenced Documents

C478M-19

Standard Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric) (Withdrawn 2020)

C822-21

Standard Terminology Relating to Concrete Pipe and Related Products

C478-19

Standard Specification for Circular Precast Reinforced Concrete Manhole Sections

C443M-21

Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)

C443-21

Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

C990-09(2019)

Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants

C969M-19

Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric)

C969-19

Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines

C928/C928M-20a

Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs (Includes all amendments and changes 10/13/2020).

C923M-18

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals (Metric) (Withdrawn 2020)

C923-18

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals

C881/C881M-20a

Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete (Includes all amendments and changes 10/14/2020).

C1244-11

Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill

C1244M-11

Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill (Metric)

C1478-19

Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals

C1478M-19

Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals (Metric) (Withdrawn 2020)

D2487-17e1

Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) (Includes all amendments and changes 4/2/2020).

D2488-17e1

Standard Practice for Description and Identification of Soils (Visual-Manual Procedures) (Includes all amendments and changes 4/4/2018).

C990M-09(2019)

Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

C1107/C1107M-20

Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)

F2510/F2510M-22

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes

29 CFR Part 1926

Safety and Health Regulations for Construction Available from U.S. Government Printing Office, Superintendent of Documents, 732 N. Capitol St., NW, Washington, DC 20401-0001, http://www.access.gpo.gov.

C858-19

Standard Specification for Underground Precast Concrete Utility Structures