ASTM A861-04(2017) - 1.10.2017
 
1. Scope

1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.

1.4 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Table 2 and Figs. 1-71 or other sizes that shall be permitted to conform to the requirements given herein.

TABLE 1 Tolerances for High-Silicon Iron Hub/Plain-End Pipe

Note 1: 1 in. = 25.4 mm.

Size, in.

Wall Thickness, in.

ID Tolerance, in.

OD Tolerance, in.

 2

±1/32 

±1/32 

±1/32 

 3

±1/32 

±1/32 

±1/32 

 4

±1/32 

±1/32 

±1/32 

 6

±1/32 

±1/32 

±3/64 

 8

±1/32 

±1/8  

±1/8  

10

±1/8  

±1/8  

±1/8  

12

±1/8  

±1/8  

±1/8  

15

±1/8  

±1/8  

±1/8  

TABLE 2 Tolerances for High-Silicon Iron Fittings

Note 1: 1 in. = 25.4 mm.

Size, in.

ID Tolerance,
in.

OD Tolerance,
in.

Stop Lug Depth
Tolerance, in.

   11/2 

±1/16 

±1/16 

±1/16 

   11/2 × 11/2 

±1/16 

±1/16 

±1/16 

   2

±1/16 

±1/16 

±1/16 

   2 × 11/2 

±1/16 

±1/16 

±1/16 

   2 × 2

±1/16 

±1/16 

±1/16 

   3

±1/16 

±1/16 

±1/16 

   3 × 11/2 

±1/16 

±1/16 

±1/16 

   3 × 2

±1/16 

±1/16 

±1/16 

   3 × 3

±1/16 

±1/16 

±1/16 

   4

±1/16 

±1/16 

±1/16 

   4 × 11/2 

±1/16 

±1/16 

±1/16 

   4 × 2

±1/16 

±1/16 

±1/16 

   4 × 3

±1/16 

±1/16 

±1/16 

   4 × 4

±1/16 

±1/16 

±1/16 

TABLE 3 Chemical Composition

Element

Composition, Weight %

Grade 1

Grade 2

Carbon

 0.65–1.10

 0.75–1.15

Manganese

 1.50 max

 1.50 max

Silicon

14.20–14.75

14.20–14.75

Chromium

 0.50 max

 3.25–5.00

Molybdenum

 0.50 max

 0.40-0.60

Copper

 0.50 max

 0.50 max

FIG. 1 No-Hub Pipe (MJ)


Size, in.

J, in.

F, in.

t, in.

11/2 

23/16 (2.19)

84

5/16 

2 

211/16 (2.69)

84

5/16 

3 

349/64 (3.77)

84

5/16 

4 

449/64 (4.77)

84

5/16 

Note 1: 1 in. = 25.4 mm.

FIG. 2 Quarter Bends


Size, in.

D, in.

ID, in.

OD, in.

Stop Lug
Depth (P), in.

11/2 

41/4 

11/2 

23/16 (2.19)

11/32 

2

41/2 

2

25/8 (2.62)

11/32 

2 × 11/2 

43/16 × 41/2 

2 × 11/2 

25/8 × 23/16 

11/32 

3

5

3

33/4 (3.75)

11/32 

4

51/2 

4

43/4 (4.75)

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 3 Sixth Bends


Size, in.

D, in.  

ID, in.  

OD, in.

Stop Lug
Depth (P), in.

   11/2 

   3

   11/2 

   23/16 

11/32 

   2

   31/4 

   2

   25/8 

11/32 

   3

   31/2 

   3

   33/4 

11/32 

   4

   33/4 

   4

   43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 4 Return Bends


 Size,
 in.

 C,
 in.

D,
in.

 F,
 in.

R,
in.

ID,
in.

OD,
in.

Stop Lug Depth (P), in.

  11/2 
  2

 4
 43/4 

2
2

 53/32 
 511/16 

2
23/8 

11/2 
2

  23/16 
  25/8 

11/32 
11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 5 Double-Branch Quarter Bend


Size,
in.

D,
in.

E,
in.

ID,
in.

OD,
in.

Stop Lug Depth (P), in.

11/2 

37/8 

33/4 

11/2 

23/16 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 6 Eight Bends


  Size,
  in.

  D,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

  11/2 

  21/2 

  11/2 

  23/16 

11/32 

  2

  23/4 

  2

  25/8 

11/32 

  3

  3

  3

  33/4 

11/32 

  4

  31/4 

  4

  43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 7 Sixteenth Bends


  Size,
  in.

  D,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

  11/2 

  2

  11/2 

  23/16 

11/32 

  2

  21/8 

  2

  25/8 

11/32 

  3

  21/4 

  3

  33/4 

11/32 

  4

  23/8 

  4

  43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 8 Long-Sweep Quarter Bends

FIG. 9 Sanitary Y Branches


Size,
in.

D,
in.

F,
in.

G,
in.

 ID,
 in

OD,
in.

Stop Lug Depth (P), in.

1/2 × 11/2 

45/8 

 61/2 

17/8 

11/2 × 11/2 

23/16 × 23/16 

11/32 

2 × 11/2 

47/8 

 61/2 

15/8 

2 × 11/2 

25/8 × 23/16 

11/32 

2 × 2

45/8 

 63/8 

2

2 × 2

25/8 × 25/8 

11/32 

3 × 11/2 

55/8 

 61/2 

11/4 

3 × 11/2 

33/4 × 23/16 

11/32 

3 × 2

57/8 

 71/8 

11/2 

3 × 2

33/4 × 25/8 

11/32 

3 × 3

63/8 

 85/8 

21/4 

3 × 3

33/4 × 33/4 

11/32 

4 × 11/2 

65/8 

 71/2 

13/8 

4 × 11/2 

43/4 × 23/16 

11/32 

4 × 2

65/8 

 71/2 

13/8 

4 × 2

43/4 × 25/8 

11/32 

4 × 3

71/8 

 83/4 

13/4 

4 × 3

43/4 × 33/4 

11/32 

4 × 4

75/8 

101/4 

25/8 

4 × 4

43/4 × 43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 10 Double-Branch Sanitary Y


Size, 

D,

F,

G,

ID,  

OD,

Stop Lug

in. 

in.

in.

in.

in.   

in.

Depth (P), in.

11/2 × 11/2 

45/8 

61/2 

17/8 

11/2 × 11/2 

23/16 × 23/16 

11/32 

2 × 11/2 

47/8 

61/2 

15/8 

2 × 11/2 

25/8 × 23/16 

11/32 

2 × 2

45/8 

63/8 

2

2 × 2

25/8 × 25/8 

11/32 

3 × 11/2 

55/8 

61/2 

11/4 

3 × 11/2 

33/4 × 23/16 

11/32 

3 × 2

57/8 

71/8 

11/2 

3 × 2

33/4 × 25/8 

11/32 

3 × 3

63/8 

85/8 

21/4 

3 × 3

33/4 × 33/4 

11/32 

4 × 2

65/8 

71/2 

13/8 

4 × 2

43/4 × 25/8 

11/32 

4 × 3

71/8 

83/4 

13/4 

4 × 3

43/4 × 33/4 

11/32 

4 × 4

75/8 

101/4 

25/8 

4 × 4

43/4 × 43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 11 Sanitary Combination Y and 1/8 
Bend


Size,
in.

D,
in.

E,
in.

F,
in.

G,
in.

ID,
in.

OD,
in.

Stop Lug
Depth
(P), in.

11/2 × 11/2 

  43/4 

53/8 

 61/2 

17/8 

  1/2 × 11/2 

23/16 × 23/16 

11/32 

2 × 11/2 

  43/4 

53/4 

 61/2 

15/8 

  2 × 11/2 

25/8 × 23/16 

11/32 

2 × 2

  5

57/8 

 65/8 

17/8 

  2 × 2

25/8 × 25/8 

11/32 

3 × 11/2 

  4

51/4 

 61/2 

15/8 

  3 × 11/2 

33/4 × 23/16 

11/32 

3 × 2

  5

61/4 

 71/8 

11/2 

  3 × 2

33/4  × 25/8 

11/32 

3 × 3

  61/4 

7

 81/2 

21/4 

  3 × 3

33/4 × 33/4 

11/32 

4 × 11/2 

  45/16 

61/8 

 65/8 

13/8 

  4 × 11/2 

43/4 × 23/16 

11/32 

4 × 2

  5

63/8 

 73/8 

13/8 

  4 × 2

43/4 × 25/8 

11/32 

4 × 3

  6

71/4 

 83/4 

13/4 

  4× 3

43/4 × 33/4 

11/32 

4 × 4

  73/8 

8 

101/4 

25/8 

  4× 4

43/4 × 43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 12 Double-Branch Sanitary Combination Y and 1/8 Bend


Size,
in.

D,
in.

E,
in.

F,
in.

G,
in.

ID,
in.

OD,
in.

Stop Lug
Depth
(P), in.

11/2 × 11/2 

 43/4 

 53/8 

 61/2 

77/8 

11/2 × 11/2 

23/16 × 23/16 

11/32 

2 × 11/2 

 43/4 

 53/4 

 61/2 

15/8 

2 × 11/2 

25/8 × 23/16 

11/32 

2 × 2

 5

 57/8 

 65/8 

15/8 

2 × 2

25/8 × 25/8 

11/32 

3 × 11/2 

 41/4 

 51/4 

 61/2 

15/8 

3 × 11/2 

33/4 × 23/16 

11/32 

3 × 2

 5

 61/4 

 71/8 

11/2 

3 × 2

33/4 × 25/8 

11/32 

3 × 3

 61/4 

 7

 81/2 

21/4 

3 × 3

33/4 × 33/4 

11/32 

4 × 2

 5

 63/8 

 73/8 

13/8 

4 × 2

43/4 × 25/8 

11/32 

4 × 3

 6

 71/4 

 83/4 

13/4 

4 × 3

43/4 × 33/4 

11/32 

4 × 4

 73/8 

  8

101/4 

25/8 

4 × 4

43/4 × 43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 13 Sanitary T Branches


Size, in.

E, in.

F, in.

G, in.

ID, in.

OD, in.

Stop Lug
Depth (P), in.

11/2 × 11/2 

41/4 

63/4 

41/4 

   11/2 × 11/2 

  23/16 × 23/16 

11/32 

2 × 11/2 

41/2 

63/4 

41/4 

   2 × 11/2 

  25/8 × 23/16 

11/32 

2 × 11/2 × 11/2 

41/2 

63/4 

41/4 

   2 × 11/2 × 11/2 

  25/8 × 23/16 × 23/16 

11/32 

2 × 2

41/2 

67/8 

41/2 

   2 × 2

  2 5/8 × 25/8 

11/32 

3 × 11/2 

5 

63/4 

41/4 

   3 × 11/2 

  33/4 × 23/16 

11/32 

3 × 2

5 

71/4 

41/2 

   3 × 2

  33/4 × 2 5/8 

11/32 

3 × 3

5 

83/8 

5  

   3× 3

  33/4 × 33/4 

11/32 

4 × 11/2 

59/16 

67/8 

 47/32 

   4× 11/2 

  43/4 × 23/16 

11/32 

4 × 2

51/2 

71/4 

41/2 

   4 × 2

  43/4 × 25/8 

11/32 

4 × 3

51/2 

81/4 

5  

   4 × 3

  43/4 × 33/4 

11/32 

4 × 4

51/2 

93/8 

51/2 

   4 × 4

  43/4 × 43/4 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 14 Double-Branch Sanitary T


Size,
in.

E,
in.

F,
in.

G,
in.

ID,
in.

OD,
in.

Stop Lug
Depth (P), in.

 11/2 × 11/2 

41/4 

63/4 

41/4 

 11/2 × 11/2 

  23/16 × 23/16 

11/32 

 2 × 11/2 

41/2 

63/4 

41/4 

 2 × 11/2 

  25/8 × 23/16 

11/32 

 2 × 2

41/2 

67/8 

41/2 

 2 × 2

  25/8 × 25/8 

11/32 

 3 × 11/2 

5

63/4 

41/4 

 3 ×11/2 

  33/4 × 23/16 

11/32 

 3 × 2

5

71/4 

41/2 

 3 × 2

  33/4 × 25/8 

11/32 

 3 × 3

5

83/8 

5

 3 × 3

  33/4 × 33/4 

11/32 

 4 × 2

51/2 

71/4 

41/2 

 4 × 2

  43/8 × 25/8 

11/32 

 4 × 3

51/2 

81/4 

5

 4 × 3

  43/4 × 33/4 

11/32 

 4 × 4

51/2 

93/8 

51/2 

 4 × 4

  43/8 × 43/8 

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 15 Sanitary Running Traps


Size,
in.

A,
in.

B,
in.

C,
in.

D,
in.

J,
in.

R,
in.

ID,
in.

OD,
in.

Stop Lug
Depth (P), in.

  11/2 

  23/4 

   15/8 

  5

10

  4

  13/4 

  11/2 

 23/16 

  11/32 

  2

  31/2 

   115/16 

  51/2 

11

  4

  2

  2

 25/8 

  11/32 

  3

  4

   25/16 

  61/2 

13

  51/2 

  21/2 

  3

 33/4 

  11/32 

  4

  41/2 

   3

  71/2 

15

  61/2 

  3

  4

 43/4 

  11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 16 Sanitary P Traps


  Size,
  in.

  A,
  in.

  B,
  in.

  C,
  in.

  D,
  in.

  J,
  in.

  R,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

  11/2 

  33/4 

 15/8 

  31/2 

  63/4 

  4

   13/4 

  11/2 

 23/16 

  11/32 

  2

  4

 115/16 

  4

  71/2 

  4

   2

  2

 25/8 

  11/32 

  3

  41/2 

 25/16 

  5

  9

  51/2 

   21/2 

  3

 33/4 

  11/32 

  4

  5

 3

  6

  101/2 

  61/2 

   3

  4

 43/4 

  11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 17 Swivel Trap P-Style, Short


  Size,
  in.

  C,
  in.

  D,
  in.

  E,
  in.

  F,
  in.

  G,
  in.

  H,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

  11/2 
  2

  83/4 
  93/4 

  4
  41/2 

 615/16 
 73/4 

  57/16 
  53/4 

  13/32 
  13/8 

  121/2 
  12

  11/2 
  2

  23/16 
  25/8 

11/32 
11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 18 Swivel Trap P-Style, Long


Size,
in.

CA,
in.

D,
in.

E,
in.

F,
in.

G,
in.

HA,
in.

ID,
in.

OD,
in.

Stop Lug Depth (P), in.

11/2 

123/4 

4

615/16 

57/16 

13/32 

121/2 

11/2 

23/16 

11/32 


(A) For shorter C or H dimension, snap-cut to desired length.

Note 1: 1 in. = 25.4 mm.

FIG. 19 Swivel Type-S Style, Long


  Size,
  in.

  C,
  in.

  F,
  in.

  G,
  in.

  H,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

   11/2 
   2

  6
  63/8 

  8
  101/2 

  143/8 
  12

  223/4 
  175/8 

  11/2 
  2

  23/16 
  25/8 

11/32 
11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 20 Centrifugal Drum Trap P Swivel Type

FIG. 21 Centrifugal Drum Trap S Swivel Type


  Size,
  in.

  C,
  in.

  D,
  in.

  E,
  in.

  F,
  in.

  J,
  in.

  ID,
  in.

  OD,
  in.

Stop Lug Depth (P), in.

   11/2 

  4

  53/32 

  63/4 

  123/4 

  4

  11/2 

  11/8 

11/32 

   11/2 

  4

  1515/32 

  63/4 

  123/4 

  4

  11/2 

  11/8 

11/32 

   2

  43/4 

  511/16 

  79/16 

  141/4 

  43/4 

  2

  2

11/32 

Note 1: 1 in. = 25.4 mm.

FIG. 22 Combination Cleanout and Test Tees


Size, in.

B,
in.

E,
in.

F,
in.

G,
in.

2

     27/16 

    33/4 

    67/8 

     37/16 

3

     33/8 

    411/16 

    83/8 

     43/16 

4

     37/8 

    57/16 

    93/8 

     411/16 

Note 1: 1 in. = 25.4 mm.

FIG. 23 Coupling


Size, in.

A, in.

B, in.

 11/2 

   33/8 

   27/8 

2

   4

   33/8 

3

   47/16 

   43/16 

4

   415/16 

   53/16 

Note 1: 1 in. = 25.4 mm.

FIG. 24 Pipe Plugs


Size, in.

F, in.

1/2 

2 

2

21/2 

3

21/2 

4

21/2 

Note 1: 1 in. = 25.4 mm.

FIG. 25 Cleanout Plugs


Size, in.

A, in.

D, in.

E, in.

F, in.

   11/2 

23/16 

21/4 

15/16 

39/16 

   2

221/32 

21/4 

15/16 

39/16 

   3

33/4 

21/2 

13/8 

37/8 

   4

43/4 

23/4 

17/16 

43/16 

Note 1: 1 in. = 25.4 mm.

FIG. 26 Adapter/Hub to No-Hub


Size, in.   

A, in.

B, in.

E, in.

F, in.

11/2 × 11/2 

323/32 

21/4 

9/16 

45/8 

11/2 × 2

313/16 

221/32 

9/16 

45/8 

11/2 × 3

313/16 

313/16 

9/16 

45/8 

11/2 × 4

313/16 

413/16 

9/16 

47/8 

2 × 2

45/16 

223/32 

5/8 

51/8 

2 × 3

45/16 

313/16 

5/8 

43/4 

2 × 4

45/16 

413/16 

5/8 

5

3 × 3

55/16 

313/16 

11/16 

53/8 

4 × 4

69/32 

47/8 

11/16 

59/16 

Note 1: 1 in. = 25.4 mm.

FIG. 27 Reducers-Increasers


Size, in.

B, in.

F, in.

    2 × 11/2 

11/2 

8

    3 × 11/2 

11/2 

8

    3 × 2

11/2 

8

    4 × 11/2 

11/2 

8

    4 × 2

11/2 

8

    4 × 3

11/2 

8

Note 1: 1 in. = 25.4 mm.

FIG. 28 Sink Outlet


Size, in.

A, in.

B, in.

C, in.

D, in.

E, in.

F, in.

11/2 

0 to 2

101/4 

17/8 

35/16 

1/4 

23/16 

Note 1: 1 in. = 25.4 mm.

FIG. 29 Sink Overflows


A, in.A

B, in.A

C, in.

4

 61/8 

1

6

 81/8 

1

8

101/8 

1


(A) Dimension A and B will vary depending upon the sink strainer in which overflow is placed, depth of counterbore, and so forth, Dimension B is given only as a guide.

Note 1: 1 in. = 25.4 mm.

FIG. 30 Threaded Adapters


Type

Size, in.

AD-7

   11/2 Outlet to 11/2 MJ

AD-8

   11/2 Outlet to 2 MJ

AD-10

   2 Outlet to 2 MJ

Note 1: 1 in. = 25.4 mm.

FIG. 31 Trap Cleanout Details

Note 1: 1 in. = 25.4 mm.

FIG. 32 Adapter – No-Hub and Split Flange


Size, in.

A, in.

J, in.

2

53/4 

6 

3

7 

71/2 

4

8

9 

Note 1: Flange dimensions are 150 lb ANSI standard.

Note 2: 1 in. = 25.4 mm.

FIG. 33 MJ to Lead Adapter


Type 

Size, in.

B, in.

C, in.

D, in.

  AD-11
  AD-12

  11/2 
  2

21/4 
223/32 

11/2 
11/2 

   125/32 
   29/32 

Note 1: 1 in. = 25.4 mm.

FIG. 34 Floor Drains

Note 1: 1 in. = 25.4 mm.

FIG. 35 Hub and Plain End Pipe


Size, in.

A, in.

B, in.

C, in.

D, in.

E, in.

F, in.

   2

 49/16 

  43/16 

  35/16 

  21/32 

  211/16 

  25/8 

   3

 55/16 

  53/16 

  45/16 

  31/8 

  325/32 

  25/8 

   4

 63/8 

  63/16 

  55/16 

  41/8 

  425/32 

  25/8 

   6

 817/32 

  811/32 

  75/16 

  515/16 

  611/16 

  3

   8

 111/4 

  103/4 

  95/8 

  81/4 

  9

  3

  10

 141/4 

  133/4 

  121/4 

  10

  111/4 

  37/8 

  12

 163/4 

  16

  141/2 

  12

  131/4 

  4

  15

 201/4 

  193/4 

  173/4 

  15

  163/4 

  41/8 

Size, in.

t, in.

Weight, lb

Working
Length, ft

Overall Length

 2

 5/16 

0.31

7

  7 ft 25/8 in.

 3

 5/16 

0.31

7

  7 ft 25/8 in.

 4

 5/16 

0.31

7

  7 ft 25/8 in.

 6

 13/32 

0.40

7

  7 ft 3 in.

 8

 13/32 

0.40

7

  7 ft 3 in.

10

 5/8 

0.62

7

  7 ft 37/8 in.

12

 5/8 

0.62

5

  5 ft 4 in.

15

 7/8 

0.75

5

  5 ft 41/8 in.

Note 1: 1 in. = 25.4 mm.

FIG. 36 Straight Tees


Size, in.

Weight,
lb

A, in.

B, in.

C, in.

  2 × 11/2 

    11

  81/2 

  17/8 

   65/8 

  2 × 2

    12

  9

  2

   7

  3 × 2

    17

  9

  21/2 

   613/16 

  3 × 3

    19

  10

  21/2 

   71/2 

  4 × 2

    20

  9

  3

   7

  4 × 3

    221/2 

  10

  3

   71/4 

  4 × 4

    26

  11

  3

   8

Note 1: 1 in. = 25.4 mm.

FIG. 37 Sanitary T Branches


Size, in.

Weight, lb

A, in.

B, in.

C, in.

  2 × 11/2 

  11

81/2 

31/2 

63/4 

   2 × 2

  12

9

31/2 

7

   3 × 11/2 

  16

81/2 

4

63/4 

   3 × 2

  18

9

4

7

   3 × 3

  20

10

4

71/2 

   4 × 11/2 

  18

81/2 

41/2 

63/4 

   4 × 2

  19

9

41/2 

7

   4 × 3

  26

10

41/2 

71/2 

   4 × 4

  28

11

41/2 

8

   6 × 2

  31

9

51/2 

7

   6 × 3

  33

10

51/2 

71/2 

   6 × 4

  35

11

51/2 

8

   6 × 6

  50

13

51/2 

9

   8 × 4

  62

105/8 

61/4 

8

   8 × 6

  65

141/2 

65/8 

101/2 

   8 × 8

 113

19

65/8 

131/2 

  10 × 6

 130

141/4 

75/8 

101/2 

  10 × 10

 180

21

73/4 

141/2 

  12 × 8

 187

19

83/4 

131/2 

Note 1: 1 in. = 25.4 mm.

FIG. 38 Sanitary Y Branches


Size, in.

Weight, lb 

A, in.

B, in.

C, in.

   2 × 11/2 

 11  

85/8 

43/8 

43/8 

   2 × 2

 12  

9

41/4 

43/4 

   3 × 11/2 

 16  

85/8 

51/16 

37/8 

   3 × 2

 17  

9

5

43/16 

   3 × 3

 21  

101/2 

51/2 

5

   4 × 11/2 

 17  

91/8 

513/16 

37/8 

   4 × 2

 21  

9

53/4 

311/16 

   4 × 3

 26  

101/2 

61/4 

41/2 

   4 × 4

 30  

12

63/4 

51/4 

   6 × 2

 28  

9

71/8 

211/16 

   6 × 3

 35  

101/2 

75/8 

31/2 

   6 × 4

 45  

121/4 

81/4 

41/4 

   6 × 6

 60  

143/4 

91/8 

53/4 

   8 × 2

 60  

167/8 

9

41/2 

   8 × 3

 63  

121/8 

9

33/4 

   8 × 4

 65  

131/2 

10

41/2 

   8 × 6

 79  

161/2 

11

61/16 

   8 × 8

117  

191/2 

121/4 

71/4 

  10 × 4

160  

131/2 

111/2 

31/2 

  10 × 6

165  

165/8 

131/2 

37/8 

  10 × 8

170  

193/4 

143/8 

43/8 

  10 × 10

180  

221/2 

15

75/8 

  12 × 4

173  

181/4 

153/16 

41/2 

  12 × 6

196  

181/4 

161/2 

41/2 

  12 × 8

200  

233/8 

151/2 

5

  12 × 10

275  

27

191/2 

6

  12 × 12

288  

251/2 

183/8 

71/4 

  15 × 15

455

321/8 

223/4 

81/8 

Note 1: 1 in. = 25.4 mm.

FIG. 39 Double-Branch Sanitary Tee

FIG. 40 Double-Branch Sanitary Y


Size, in.

Weight, lb

A, in.

B, in.

C, in.

2 × 11/2 

14

85/8 

43/8 

43/8 

2 × 2

15

9

41/4 

43/4 

3 × 11/2 

19

85/8 

51/16 

37/8 

3 × 2

20

9

5

43/16 

3 × 3

28

101/2 

51/2 

5

4 × 11/2 

21

91/8 

513/16 

37/8 

4 × 2

23

9

53/4 

311/16 

4 × 3

26

101/2 

61/4 

41/2 

4 × 4

33

12

63/4 

51/4 

6 × 2

31

9

71/8 

211/16 

6 × 3

46

101/2 

75/8 

31/2 

6 × 4

52

12

81/8 

41/4 

6 × 6

65

143/4 

91/8 

53/4 

8 × 4

71

131/2 

10

101/2 

8 × 6

86

161/2 

11

61/16 

Note 1: 1 in. = 25.4 mm.

FIG. 41 Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)


Size, in.

Weight,
 lb

A, in.

B and B,
in.

C, in.

E, in.

2 × 11/2 

15 

85/8 

91/4 

43/8 

73/8 

2 × 2

17 

9

101/2 

43/4 

81/4 

3 × 11/2 

17 

85/8 

101/4 

37/8 

73/8 

3 × 2

22 

9

111/2 

43/16 

83/16 

3 × 3

27 

101/2 

13

5

99/16 

4 × 11/2 

24 

91/8 

113/4 

37/8 

81/8 

4 × 2

24 

9

121/2 

311/16 

83/16 

4 × 3

28 

101/2 

14

41/2 

99/16 

4 × 4

40 

12

151/2 

51/4 

1013/16 

6 × 3

45 

101/2 

16

31/2 

99/16 

6 × 4

57 

12

171/2 

41/4 

1013/16 

6 × 6

83 

15

201/2 

53/4 

137/16 

Note 1: 1 in. = 25.4 mm.

FIG. 42 Short-Sweep Quarter Bends


Size, in.

Weight, lb

B, in.

C, in.

2

11

51/4 

 8

3

20

6 

 9

4

25

61/2 

10

Note 1: 1 in. = 25.4 mm.

FIG. 43 Long-Sweep Quarter Bends


Size,
in.

Weight,  
lb

B,
in.

C,
in.

2

14  

81/2 

12

3

24  

9

121/2 

4

29  

91/2 

13

6

47  

101/2 

14

8

98

111/8 

15

Note 1: 1 in. = 25.4 mm.

FIG. 44 Sanitary Combination Y and 1/8 Bend (T-Y)


Size,
 in.

Weight,
  lb

A,
in.

B,
in.

C,
in.

E,
in.

 2 × 11/2 

 11

85/8 

45/8 

43/8 

73/8 

 2 × 2

 13

9

51/4 

43/4 

81/4 

 3 × 11/2 

 14

85/8 

51/8 

37/8 

73/8 

 3 × 2

 18

9

53/4 

43/16 

83/16 

 3 × 3

 24

101/2 

61/2 

5

99/16 

 4 × 11/2 

 17

91/8 

57/8 

37/8 

81/8 

 4 × 2

 21

9

61/4 

311/16 

83/16 

 4 × 3

 23

101/2 

7

41/2 

99/16 

 4 × 4

 31

12

73/4 

51/4 

103/16 

 6 × 2

 33

9

71/4 

211/16 

83/16 

 6 × 3

 37

101/2 

8

31/2 

99/16 

 6 × 4

 47

12

83/4 

41/4 

1013/16 

 6 × 6

 63

15

101/4 

53/4 

137/16 

10 × 6

185

163/4 

121/2 

47/16 

43/8 

10 × 8

192

213/8 

151/8 

61/2 

181/2 

Note 1: 1 in. = 25.4 mm.

FIG. 45 Quarter Bends


Size,
in.

Weight,
lb

B,
in.

C,
in.

2

  9

31/2 

7

3

 16

4

71/2 

4

 20

41/2 

8

6

 36

51/2 

9

8

 54

61/8 

10

10

116

85/8 

12

12

195

103/8 

14

Note 1: 1 in. = 25.4 mm.

FIG. 46 Sixth Bends


Size,
in.

Weight,
lb

 B,
 in.

 C,
 in.

2

 8

21/4 

53/4 

3

11

21/2 

6

4

15

23/16 

65/16 

6

27

33/8 

67/8 

8

71

41/8 

9

Note 1: 1 in. = 25.4 mm.

FIG. 47 Eighth Bends


Size,
in.

Weight,
lb

B,
in.

C,
in.

 2

  7

13/4 

51/4 

 3

 13

115/16 

57/16 

 4

 16

23/16 

511/16 

 6

 25

29/16 

61/16 

 8

 46

311/16 

813/16 

10

 95

41/4 

91/4 

12

132

5

95/8 

Note 1: 1 in. = 25.4 mm.

FIG. 48 Sixteenth Bends


Size,
in.

Weight,
lb

 B,
 in.

 C,
 in.

2

 6

11/8 

45/8 

3

 8

13/16 

411/16 

4

11

15/16 

413/16 

6

21

11/2 

5

8

44

21/16 

71/8 

10

80

2

67/8 

Note 1: 1 in. = 25.4 mm.

FIG. 49 Sanitary Increasers


Size,
in.

Weight,
lb

A,
in.

    2 × 3

 9

9

    2 × 4

13

9

    2 × 6

17

9

    3 × 4

17

9

    3 × 6

16

9

    4 × 6

17

9

    4 × 8

33

115/8 

    6 × 8

50

117/8 

    8 × 10

85

16

Note 1: 1 in. = 25.4 mm.

FIG. 50 Hub Strainers


Size,
in.

Weight,
lb

2

        21/2 

3

        3

4

        5

6

        10

8

        18

Note 1: 1 in. = 25.4 mm.

FIG. 51 Sanitary Reducers


Size,
in.

Weight,
lb

A, in.

 

3 × 11/2 

 6

5

 

3 × 2

 7

5

 

4 × 11/2 

 7

5

 

4 × 2

 9

5

 

4 × 3

11

5

 

6 × 2

12

5

 

6 × 3

13

5

 

6 × 4

14

5

 

8 × 4

22

6

 

8 × 6

25

6

 

10 × 6

39

6

 

10 × 8

51

6

 

12 × 6

55

 61/2 

 

12 × 8

65

6

 

12 × 10

83

6

 

15 × 6

79

6

 

15 × 12

109 

6

Note 1: 1 in. = 25.4 mm.

FIG. 52 Double Hubs


Size,
in.

Weight,
lb

A,
in.

 2

61/2 

1

 3

9 

1

 4

12

1

 6

18

1

 8

40

2

10

82

2

Note 1: 1 in. = 25.4 mm.

FIG. 53 Pipe Plugs


Size,
in.

Weight,
lb

 2

 2

 3

 3

 4

 5

 6

10

 8

17

12

56

Note 1: 1 in. = 25.4 mm.

FIG. 54 Cleanout Plugs


Size,
in.

Weight,
lb

 2

31/2 

 3

61/2 

 4

11 

 6

14 

 8

26 

10

39 

Note 1: 1 in. = 25.4 mm.

FIG. 55 Adapter – Plain End and Split Flange


Size,
in.

Weight,
lb

A,
in.

J,
in.

2

 5

   53/4 

   6

3

11

   7

   71/2 

4

12

   8

   9

6

22

   91/2 

   11

8

44

   103/4 

   131/2 

Note 1: 1 in. = 25.4 mm.

FIG. 56 Adapter – Hub and Split Flange


Size,
in.

Weight,
lb

A,
in.

J,
in.

2

 5

21/2 

6 

3

 7

21/2 

71/2  

4

12

23/4 

9 

6

16

3  

11  

8

36

31/2 

131/2 

Note 1: 1 in. = 25.4 mm.

FIG. 57 Combination Cleanout and Test Tees


Size,
in.

Weight,
lb

A,
in.

B,
in.

 C,
 i n.

D,
in.

E,
in.

F,
in.

2

12

21/2  

 9

 313/16 

35/8 

31/16 

 27/8 

3

22

27/8  

10

 5

45/8 

41/4  

 313/16 

4

29

39/16 

11

 57/16 

55/8 

41/2  

 413/16 

Note 1: 1 in. = 25.4 mm.

FIG. 58 Insertable Joints


Plate No.

Size,
in.

Weight,
lb

A,
in.

B,
in.

5045

2

11

73/4 

61/2 

5070

3

17

83/8 

73/8 

5095

4

21

91/8 

77/8 

5144

6

37

91/8 

77/8 

Note 1: 1 in. = 25.4 mm.

FIG. 59 Backwater Valves


Size, in.

3

4

6

8

Note 1: 1 in. = 25.4 mm.

FIG. 60 Sanitary P Traps


Size,
in.

Without
Vent
Weight, lb

Hub
Vent
Weight, lb

A,
in.

B,
in.

C,
in.

D,
in.

E,
in.

G,
in.

H,
in.

Vent,
in.

2

12

16

11

3

61/4 

41/2 

21/4 

  313/16 

  15/8 

2

3

25

32

121/2 

41/4 

61/4 

51/2 

3

  41/2 

  25/16 

3

4

37

45

14

51/2 

7

61/2 

31/4 

  53/16 

  3

4

6

68

80

17

81/2 

8

81/2 

4

  61/2 

  315/16 

4

Note 1: Depth of seal on all traps shall be 21/2 in.

Note 2: 1 in. = 25.4 mm.

FIG. 61 Sanitary S Traps


Size,
in.

Without
Vent,
Weight, lb

Hub
Vent,
Weight, lb

A,
in.

B,
in.

C,
in.

D,
in.

E,
in.

F,
in.

G,
in.

H,
in.

Vent,
in.

2

16

18

91/4  

3

 8

41/2 

33/4 

43/4 

  313/16 

  15/8 

2

3

24

29

101/2 

41/4 

10

51/2 

41/4 

61/4 

  41/2 

  25/16 

3

4

33

39

111/4 

51/2 

12

61/2 

41/4 

7

  53/16 

  3

4

6

82

89

14

81/2 

16

81/2 

5

9

  61/2 

  315/16 

4

Note 1: Depth of seal on all traps shall be 21/2 in.

Note 2: 1 in. = 25.4 mm.

FIG. 62 Sanitary Running Traps


Size,
in.

Without
Vent,
Weight, lb

Single
Hub Vent,
Weight, lb

Double
Hub Vent,
Weight, lb

A,
in.

B,
in.

D,
in.

E,
in.

F,
in.

G,
in.

H,
in.

Vent,
in.

 2

 14

 17

 22

131/2 

21/2 

41/2 

21/2 

51/4 

  85/16 

  15/8 

2

 3

 29

 36

 42

151/2 

3

51/2 

31/4 

61/4 

  10

  25/16 

3

 4

 41

 49

 57

171/2 

31/2 

61/2 

31/2 

71/4 

  1111/16 

  3

4

 6

 78

 87

168

211/2 

41/2 

81/2 

41/4 

81/4 

  15

  315/16 

4

 8

162

165

208

267/8 

51/2 

11

37/8 

12

  187/16 

  51/4 

6

10

330

334

346

317/8 

71/8 

13

51/8 

16

  221/4 

  611/16 

6

Note 1: Single hub vent is located on the inlet side. Depth of seal on 8- and 10-in. traps is 3 in. All others 21/2 in.

Note 2: 1 in. = 25.4 mm.

FIG. 63 Outside Caulk


Plate
No.

Outlet
Size, in.

Weight, lb

1

2, 3, 4 and 6

45

2

2, 3, 4 and 6

45

3

2, 3, 4 and 6

53

4

2, 3, 4 and 6

53

5

2, 3, 4 and 6

41

6

2, 3, 4 and 6

42

7

2, 3, 4 and 6

48

8

2, 3, 4 and 6

49

Note 1: 1 in. = 25.4 mm.

FIG. 64 Outside Caulk with Basin


Plate
No.

Size,
in.

A,
in.

B,
in.

C,
in.

5, 6, 7, 8

2

27/8 

31/2 

5/16 

 

3

37/8 

41/2 

5/16 

 

4

47/8 

51/2 

3/8  

 

6

7

73/4 

3/8 

Note 1: 1 in. = 25.4 mm.

FIG. 65 Inside Caulk

Note 1: 1 in. = 25.4 mm.

FIG. 66 Floor Drains


Plate
No.

Outlet
Size, in.

Weight, lb

1

3

70

2

4

73

3

2

37

4

2

45

Plate
No.

Size,
in.

A,
in.

B,
in.

C,
in.

D,
in.

E,
in.

F,
in.

1
2

3
4

8
8

9
9

57/8 
63/8 

11/2 
11/2 

14
14

141/2 
141/2 

Note 1: 1 in. = 25.4 mm.

FIG. 67 Method of Installation

FIG. 68 Floor Drain Funnel Attachment

Note 1: 1 in. = 25.4 mm.

FIG. 69 No. 1, 2, 3, 4, and 5 Overflows


Plate
No.

A, in.A

B, in.A

C, in.

1

2

 41/8 

1

2

4

 61/8 

1

3

6

 81/8 

1

4

8

101/8 

1

5

0

 21/8 

1


(A) Dimensions A and B will vary depending upon the sink strainer in which overflow is placed, depth of counterbars, and so forth. Dimension B is given only as a guide.

Note 1: 1 in. = 25.4 mm.

FIG. 70 Sink Outlet


Plate
No.

Size,
in.

A,
in.

B,
in.

C,
in.

D,
in.

E,
in.

1

11/2 or 2

 3/4 to 11/4 

10

31/2 

  43/8 

  1/8 

2

11/2 or 2

 1 to 2

10

21/2 

  37/8 

  7/16 

3

11/2 or 2

 1 to 2

10

21/2 

  3

  1/4 

4

11/2 

 0 to 2

101/4 

 

  35/16 

  1/4 

Note 1: Furnished with flat loose strainer plates.

Note 2: 1 in. = 25.4 mm.

FIG. 71 Detailed Cross Section of Cleanout


Size, in.

Diameter
of Drain, in.

A, in.

Under 6

11/2 

23/16 

6 and over

21/4 

29/16 

Note 1: Traps can be supplied without cleanouts, as shown in the figure.

Note 2: 1 in. = 25.4 mm.

1.4.1 Pipe: 

1.4.1.1 No-Hub (MJ) (Fig. 1): 

 

Size (in.)

Length (ft)

 

11/2 

7

 

2

7

 

3

7

 

4

7

1.4.1.2 Hub/Plain End (Fig.35): 

 

Size (in.)

Length (ft)

 

 2

7

 

 3

7

 

 4

7

 

 6

7

 

 8

7

 

10

5

 

12

5

 

15

5

1.4.2 Fitting (No-Hub) (MJ):

 

Figs.

Quarter Bends

2

Sixth Bends

3

Return Bends

4

Double-Branch Quarter Bend

5

Eighth Bends

6

Sixteenth Bends

7

Long-Sweep Quarter Bends

8

Sanitary Y Branches

9

Double-Branch Sanitary Y

10

Sanitary Combination Y and 1/8 Bend

11

Double-Branch Sanitary Combination Y and 1/8 Bend

12

Sanitary T Branches

13

Double Branch Sanitary T

14

Sanitary Running Traps

15

Sanitary P Traps

16

Swivel Trap P-Style, Short

17

Swivel Trap P-Style, Long

18

Swivel Trap S-Style, Long

19

Centrifugal Drum Trap P Swivel Type

20

Centrifugal Drum Trap S Swivel Type

21

Combination Cleanout and Test Tees

22

Coupling

23

Pipe Plugs

24

Cleanout Plugs

25

No-Hub (MJ) Adapter

26

Reducers-Increasers

27

Sink Outlet

28

Sink Overflows

29

Threaded Adapters

30

Trap Cleanout Details

31

No-Hub (MJ) Adapter

32

(MJ) (No-Hub) to Lead Adapter

33

Floor Drains

34

1.4.3 Fitting (Hub/Plain End): 

 

Figs.

Hub Plain End Pipe

35

Straight Tees

36

Sanitary T Branches

37

Sanitary Y Branches

38

Double-Branch Sanitary Tee

39

Double-Branch Sanitary Y

40

Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)

41

Short-Sweep Quarter Bends

42

Long-Sweep Quarter Bends

43

Sanitary Combination Y and 1/8 Bend (T-Y)

44

Quarter Bends

45

Sixth Bends

46

Eighth Bends

47

Sixteenth Bends

48

Sanitary Increasers

49

Hub Strainers

50

Sanitary Reducers

51

Double Hubs

52

Pipe Plugs

53

Cleanout Plugs

54

Adapter – Plain end to Split Flange

55

Adapter – Hub to-Split Flange

56

Combination Cleanout and Test Tees

57

Insertable Joints

58

Backwater Valves

59

Sanitary P Traps

60

Sanitary S Traps

61

Sanitary Running Traps

62

Floor Drains

63, 64, 65

Floor Drains

66

Floor Drains/Installation – Funnel Attachment

67, 68

Overflow

69

Sink Outlet

70

Detailed Cross Section of Cleanout

71

Chemical Composition

Table 3

Transverse Bend Test Minimum Requirements

Table S1.1

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

 
2. Referenced Documents

National Motor Freight Classification

Uniform Classification Rules Available from American Trucking Association, 950 North Glebe Road, Suite 210, Arlington, VA 22203-4181.

E351-18

Standard Test Methods for Chemical Analysis of Cast Iron´All Types

A518/A518M-99(2022)

Standard Specification for Corrosion-Resistant High-Silicon Iron Castings

E350-23

Standard Test Methods for Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron