Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
Automaticky přeložený název:
Standardní zkušební metoda pro stanovení plastovým stěně potrubí Tuhost
NORMA vydána dne 1.8.2013
Označení normy: ASTM F2433-05(2013)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2013
Kód zboží: NS-53858
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
buckling, modulus of relaxation, moment of inertia, pipe stiffness, residual pipe stiffness, ICS Number Code 23.040.20 (Plastic pipes)
Significance and Use | ||||||||||||||||||
5.1 The performance under bending and compression load of a thermoplastic plastic pipe wall design obtained by this method can be used for the following: 5.1.1 To determine the stiffness of the pipe wall section. This is a function of the pipe dimensions, the wall design, the arc length tested, and the physical properties of the material of which the pipe is made. 5.1.2 To compare the characteristics of various thermoplastic pipe wall designs. 5.1.3 To compare the characteristics of various plastics in pipe form. 5.1.4 To study the interrelations of dimensions, materials, and deformation properties of thermoplastic pipe designs. 5.1.5 To measure the deformation and load-resistance at any of several significant events which may occur during the test. 5.1.6 To provide a reasonable quality control/quality assurance test for very large diameter plastic pipes. 5.2 The time-dependent pipe wall stiffness of a thermoplastic pipe obtained by this test method may used for the following: 5.2.1 To predict the residual stiffness of the pipe wall in bending and compression at all times after initial loading. 5.2.2 For purposes of design, to determine a modulus of relaxation under sustained loads. 5.2.3 To quantify the influence of material formulations of thermoplastics on the modulus of relaxation. 5.2.4 To study the influence of geometric patterns of wall profiles on the modulus of relaxation. 5.3 The time-independent reduction of wall thickness at springline may be used for the following: 5.3.1 For pipe wall stiffness, to quantify the efficiency of all wall profiles of any material composition and a given geometry with that of a solid uniform thickness wall. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 This test method covers the determination of the load-deflection behavior of thermoplastic pipe wall sections under parallel plate loading conditions. 1.2 This test method covers a
loading test for determining the wall stiffness of a
thermoplastic-pipe wall under a combined load of bending and
compression. Changes in pipe wall profile geometry under load may
also be determined.
1.3 This test method covers thermoplastic pipe. 1.4 The characteristics determined by this test method are wall stiffness and changes in profile wall dimensions at specific deformations. 1.5 The characteristics determined by this test method are wall stiffness, profile wall efficiency, and for some wall elements stability at specific Strain levels. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.2.2013
Historická
1.4.2010
Historická
1.12.2009
Historická
1.11.2013
Historická
1.11.2011
Historická
1.8.2012
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 31.10.2024 (Počet položek: 2 208 647)
© Copyright 2024 NORMSERVIS s.r.o.