Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM E1704-95(2018)
Standard Guide for Specifying Acoustical Performance of Sound-Isolating Enclosures
Přeložit název
NORMA vydána dne 1.10.2018
Informace o normě:
Označení normy: ASTM E1704-95(2018)
Datum vydání normy: 1.10.2018
Kód zboží: NS-905931
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM E1704-95(2018) :
Keywords:
buildings, enclosures, insertion loss, level reduction, noise reduction, rooms, specifications ,, ICS Number Code 17.140.01 (Acoustic measurements and noise abatement in general)
Doplňující informace
| Significance and Use | ||||||||||||||||||
|
5.1 This guide can be used to produce a specification for the acoustical performance of an enclosure. 5.2 This guide is intended for those familiar with basic concepts of acoustics. 5.3 Although this guide provides detailed guidance in matters relating to specification of acoustical enclosures, it is not a substitute for the experience and judgment of an acoustical or noise control professional. 5.3.1 This guide calls for measurements common within acoustical practice. 5.3.2 The more critical the performance requirements of the enclosure, the more the user should consider seeking the services of an acoustics or noise control professional. 5.4 The specifying of a sound-isolating enclosure has three sequential steps: 5.4.1 Determine the sound pressure levels that exist at specific locations prior to the introduction of the enclosure, Note 1: In the case of new construction, the sound pressure
level is often estimated from the sound power levels of
noise-emitting equipment and a general description of the
acoustical properties of the environment.
5.4.2 Determine the maximum permissible sound pressure levels that must exist at the same locations after the introduction of the enclosure, and 5.4.3 Determine the required enclosure level reduction. The required isolation is related to the difference between the sound pressure levels before and after the introduction of the enclosure. 5.5 Many specifications are for multiple enclosures or enclosures with multiple functions, or both. It is beyond the scope of this guide to provide detailed guidance for every possible combination. Separate specifications for each source-enclosure-receiver combination should be used in such a case. 5.6 The type of specification that should be selected depends both on the purpose of the enclosure and how crucial its performance is. In general: 5.6.1 If exceeding a particular maximum permissible sound pressure level spectrum would render the enclosure unsuccessful, a sound pressure level specification should be used. 5.6.1.1 This guide assigns all phases of acoustical design are delegated to the supplier. Compliance is usually more easily verified than with the level reduction method. 5.6.2 If the criteria for the success of the enclosure are less stringent or not related to a specific maximum permissible spectrum, a level reduction specification may be used. |
||||||||||||||||||
| 1. Scope | ||||||||||||||||||
|
1.1 The guide covers the development of criteria for the acoustical performance of a broad variety of acoustical enclosures by identifying information necessary to unambiguously describe acoustical performance. This guide is not a standard ASTM specification for a sound-isolating enclosure. 1.2 Excluded from the scope of this guide are technical considerations for enclosure design that do not pertain directly to acoustical performance. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||
|
Doporučujeme:
